Corn Extruder Machine-manufacture,factory,supplier from China

The screw extruder was first used in the plastics industry, and its theoretical research started earlier, forming a variety of mathematical models used to describe the basic principles of flow and heat transfer in the extrusion process, using these models to achieve accurate extrusion machine simulation Design. The application of extrusion technology in the food industry is slightly later than that in the plastics industry, which is mainly due to the complexity of food raw materials.

Extruder belongs to a kind of equipment for processing puffed food. It is a kind of equipment for processing puffed food, such as processing rice, corn, soybean, wheat, etc., in daily life.

Feed extruder is a single screw extruder. Mainly used for food puffing, livestock feed or used for puffing single raw materials, but also as a plant oil and drinking wine production of raw materials in the pre-place. Twin-screw extruding extruder, mainly used for the production and processing of high-grade aquatic products, pet materials, especially the processing of viscous materials.What are its characteristics?1.

Corn chip is a kind of brittle food, with good rehydration, external flushing not rotten, smooth taste, grain flavor rich.

The extruder has the functions of compression, mixing, kneading, melting, puffing and molding. The cavity of the extruder can be divided into 3-5 zones. Each zone can be heated by steam or electricity, or by extrusion friction, so as to achieve the purpose of cooking the material. Under the action of high temperature and high pressure in the cavity, the starch Gelatinization, protein denaturation. When the material passes through each zone of the extruder cavity, soluble flavor substances and pigments can be injected into the material through the cavity under high pressure.

Screw extruder is mainly used in the production of starch extruded food, protein extruded food and extruded feed in the food industry, and can also be used as a special chemical or biochemical reactor.Starch puffed foodThe starch in the grain will gelatinize (αize) under the high temperature and pressure of the extruder. The results showed that the degree of starch αization was more than 98% and the crude fat decreased by 60% or even disappeared after the puffed corn flour. Water solubility increased by more than 40%. Therefore, extruder can replace roller dryer to produce gelatinized starch.

1. Before operating the corn equipment bulking machine, remove the head, movement, lead screw and other parts, clean them up, dry them and then install them.2. Idling for 1 to 2 minutes first when operating, put the raw materials into the feed mouth, not too fast, when the ring groove of the spiral shaft head is filled, stop feeding, friction preheating. Wait until the nose temperature rises and the pressure inside the cabin builds up before feeding.3. Feed should be continuous and uniform, material must be dry, must pay attention to.4.

There is only one screw in the barrel of the single screw extruder, it is by the friction of the screw and the barrel of the material to transport materials and form a certain pressure. In general, the friction coefficient between the material and the barrel is greater than that between the material and the screw. Otherwise, the material will be wrapped in the screw together to rotate and not play the role of forward propulsion.Screw is divided into three sections: feeding (feeding) conveying section, compression melting section, metering homogenization section.

When purchasing a large airflow puffing machine, the following points are what companies need to pay attention to:1. It is necessary to check whether the manufacturer has production conditions, production equipment, design and manufacturing capabilities, test reports from the relevant departments of the country that can provide equipment, and producer's qualification documents.2.

How it worksObviously, the material will flow from the high pressure area to the low pressure area in two directions: one is that the wear of the square screw will be reduced as the screw rotates, and the material will be transported, sheared, mixed and heated by the barrel shell in this way.Under the action of high pressure, it is matured and then squeezed out of the cylinder.The counter-rotating twin-screw extruder generally uses two screws with the same size but opposite thread directions.